store image

5m Digital RGB LED Strip Light Kit - Single Addressable Color-Chasing LED Tape Light - 12V - IP67

Part Number: SWDCK-RGB-240
11 photos
In Stock
$149.95 / kit
Volume price as low as $134.95
Orders ship on or before  Tuesday 07/05/2022
  • Select options to see various notes.


DreamColor series RGB LED Light Strip Kit provides years of outdoor illumination on decks, patios, gazebos, walkways, driveways, and railings but is also perfect for cabinet lighting, under-cabinet lighting, cove lighting, store window lighting, showcase lighting, trade show lighting, bias lighting, or for other indoor applications where space is limited. The flexible 16-1/2' strip has 240 LEDs (5050 SMD) with an output of up to 600 lumens. Adjust 29 colors and 99 dynamic color modes with the hand-held RF remote. The silicone-encased strip is waterproof for year-round outdoor use and is designed to last 40,000 hours. It operates within a wide 100-240 VAC range and can be cut into 6-LED segments. The kit includes 1 RGB LED light strip, controller with RF remote, a 12 VDC power supply, and mounting clips.

5 Years
Super Bright LEDs, Inc. offers a 5-year warranty to protect against manufacturer defects and malfunctions. If you experience failure of an LED or other component not caused by negligence, abuse, unauthorized repair or disassembly, we will replace the product within the warranty period. If the same product is no longer available, a product of equal value may be substituted. Read More
  • Gazebos
  • LED Cabinet Lighting
  • Showcases
  • Walkway
  • Storefronts
  • Coves
  • Under-Cabinets
  • Bias Lighting
  • Patios
  • Driveways
  • LED Deck Lighting
  • Trade Shows


Strip Specifications
Full Length 196.9in (16.40ft)
Section Length 12.5cm (4.92in)
Strip Width 14mm (0.55in)
Input Voltage 12 VsDC
Number of LEDs 240
LEDs per Segment 6
LED Type 5050 RGB SMD
LED Brand Epistar
LED Lifetime 40000 Hours
Water Resistance Weatherproof IP67
Beam Angle 100 degree
Intensity 600 Lumen
Wavelength 470 nm/525 nm/626 nm
Strip Finish White
Polarity Sensitive Yes
Wire Length 20.3cm(8in)
Controller Specifications
Input Voltage 12VDC
Current 3A
Water Resistance Non-Weatherproof
Remote Specifications
Type Radio (RF)
Maximum Range Up to 15m (50')
Battery Type 1 x CR2025
Power Supply Specifications
Input Voltage 90~264VAC
Input Frequency 47~63Hz
Output Voltage 12VDC
Output Current 2A Max
Total Power Consumption 60 Watts Max
Wire Length 101.6cm(40in)
Current Draw @ Operating Voltage 2800mA
Water Resistance Non-Weatherproof
Weatherproof Warning
  • The LED Light Strip included in this kit has an IP65 rating for weatherproof outdoor applications. Other components included in the kit are not suitable for outdoor use on their own. See product accessories for weatherproof housings and sealants.

 Installation Instructions & Remote Functions 

Remote Functions
  1. Power Input: The power supply input and sleeve is negative. Also please make sure the power supply voltage is same as the LED load. The DC jack’s inner pole is positive.
  2. Signal Output: The control signal output connector to LED load.
  3. Mode Adjust: Adjust running mode. Jump to next mode by press MODE+ or jump to previous mode by press MODE-.
  4. Speed (Brightness) Adjust: Adjust the running speed of dynamic mode or brightness of static color. There are 10 levels for both speed and brightness.
  5. Pause / Play: Toggle between Play and Pause mode. It will quit pause and start to play if changing the running mode.
  6. Turn On / Standby: Turn on or switch to standby mode. The main unit will memorize the current setting. When power on or turn on unit, it will automatically restore to previous status.
  7. Unit Length (Static Color) Adjust: Adjust playing unit length at dynamic modes or adjust color at static color mode. At static color mode, press these keys to loop change 20 colors.
  8. Program Direct Selecting Keys: User can directly select program by the number and Enter key in this area. For example, if you want program number 58, please press number 5 and 8, then press Enter key to confirm. The program 0 is static color mode. Press 0 twice then press "Enter". To cycle through static colors press either "Length" buttons. To dim current color press "Speed -" and to brighten current color press "Speed +". Return to dynamic color chasing modes by selecting either "Mode" buttons.
  9. Demo Mode: Switch to demo mode. In demo mode, the controller will automatically cycle play 99 dynamic programs.
  10. Remote Controller Indicator: This blue indicator will light up when remote controller works. In program direct selecting operation, this indicator will flash slowly until Enter key pressed or no operation for a certain time.
Hints: The remote controller works at radio frequency, the signal can pass through barrier, so it’s not necessary to aim at the controller when operate the remote.

Remote Pairing

The controller and remote is 1 to 1 paired as default. The controller only can be controlled by paired remote. When extra remote is needed or the controller need to be matched to any remote, user can match the remote by following combination operation.
Pairing a New Remote
Unplug the controller power and plug in again after 10 seconds. Press the ‘MODE-’ and ‘LENGTH-’ keys at same time once within 5 seconds after the power is on, then release the keys and press the ‘MODE+’ key once within another 5 seconds. The controller can be paired to maximum 5 remotes.
Pairing to Any Remote
Unplug the controller power and plug in again after 10 seconds. Press the ‘MODE-’ and ‘LENGTH-’ keys at same time once within 5 seconds after power is on, then release the keys and press the ‘DEMO’ key once within another 5 seconds.
Pairing to One Remote
Unplug controller power and plug in again after 10 seconds. Press the ‘MODE-’ and ‘LENGTH-’ keys at the same time once within 5 seconds after power is on, then release the keys and press ‘SPEED-’ key once within another 5 seconds.

Installation Instructions

Output Signal
The output signal is in a SM type plug. The cable at the button maker side is power supply, the cable sequence is power-data-clock-ground. The control signals are running at high speed, LED may not work properly if the data cable is too long or gets interfered with. In this case, shorten the data cable from controller to LED or install the controller close to LED.
Pre-test Configure
Remove strip from reel and make connections to controller and power supply (see "Method 1" diagram). Briefly turn on strip using the included remote controller to ensure proper operation of the strip, controller, power supply, and remote. See Method 1 diagram for a guide to installing and connecting LED strip to included controller and power supply for your application. Choose your desired yet suitable location for the power supply and controller. Controller can be hidden for use with RF remote control. Use mounting clips to secure LED strip to surface.
Power Supply
The power supply jack is a 5.5mm diameter DC socket. The main unit can work at DC 5V to 24V. Since the power supply is directly connected to the LED signal output, please make sure the power voltage is same as the LED load, otherwise the incorrect voltage may damage LED load. When LED load is powered individually, the main unit can also work with the LED load power, and the power supply to this DC jack can be saved.
SWDCK-RGB-240 - Color Chasing Waterproof LED Light Strip - Full Kit with Multi Color LEDs - 16.40ft (5m) Outdoor LED Tap
Color Chasing Waterproof LED Light Strip - Full Kit with Multi Color LEDs - 16.40ft (5m) Outdoor LED Tape Light with 18 SMDs/ft., 3 Chip RGB SMD LED 5050



Overall Rating

Total Reviews


Tell Us What You Think

Share your own experience and photos of this product. Doing so will help inform other potential buyers and allow us improve our product lines. It may take up to 72 hours for your review to appear.

Sign In Required to Write a Review
Click here to sign in to your account
Technical Level
Part Number
Reviewed On

Absolutely Love them!

These lights are super bright and have SO many color options! I was able to see them from almost a mile away from my business! I even had someone stop to ask me where I got them from because they were so impressed with them! I definitely plan on purchasing more of these!

Helpful? Yes (6) No (0)

Chris Dumas
Technical Level
Part Number
Reviewed On

Used on-stage

Used this lighting strip to create a jukebox for our high school's production of Grease. Installed them on the inside of a flexible "ferret" play tube and it created the "arch" of the jukebox. Each scene in the show had a different program running to match the mood. Easy to use and the remote easily worked from 80 ft. away. It really was another character in the show.

Helpful? Yes (4) No (0)

Technical Level
Part Number
Reviewed On

Pretty cool

Over all the lights are really awesome! however I decided to try and split them up and was unsuccessful at soldering them how I wanted them to go underneath cabinets. Couldn't figure out the problem, so wasn't much I could do. When its one full strip though it is really cool

Helpful? Yes (6) No (3)

Technical Level
Part Number
Reviewed On

Led light strip

I brought a set of these light strip 11 months ago, I do love the color chasing effect it has and the many color chasing option it has to offer, the only thing that is wrong with my set is that the controller gave up on me so the lights don't respond to the remote, but all in all a great product.

Helpful? Yes (1) No (0)

Technical Level
Part Number
Reviewed On

Send us your Feedback